隔舱式双脉冲发动机第Ⅱ脉冲点火过程数值仿真

基于计算流体力学和相关点火理论,对双脉冲发动机第Ⅱ脉冲点火瞬态过程的流场进行了数值分析,并进行了发动机第Ⅱ脉冲点火试车试验。结果表明：在隔板打开前,第Ⅱ脉冲燃烧室高压区的位置由燃烧室前端向隔板移动,压强沿燃烧室径向变化较小,沿轴向变化较大,燃烧室头部和尾部近壁面区域一直处于低温;6 ms时隔板打开,第Ⅱ脉冲燃烧室压强下降05 MPa,药柱内孔前后端压强差波动剧烈,药柱内孔前端温度场下降600 K,而其他区域温度变化较小。隔板打开后,沿隔板下游第Ⅰ脉冲燃烧室轴线形成带状高温区,第Ⅰ脉冲燃烧室头部和尾部依次出现压强峰值,第Ⅰ脉冲燃烧室压强在18 ms时达到稳定,而温度在25 ms时达到稳定。试验测得的第Ⅰ、Ⅱ脉冲燃烧室压强-时间曲线和仿真结果吻合较好,表明该仿真方法具有一定的准确性。     

活门型孔“化方为圆”算法

通过对航空发动机控制系统活门型孔的流量系数稳定性控制的方法进行研究,提出了一套能够将方形活门型孔转化为有规律排列组合小圆孔的算法,并通过实例验证了算法的正确性,同时转化误差小于0.7%,基本实现了工程意义上的等流量系数。该算法将加工工艺性差且计量精度低的方形活门型孔转化为有规律排列组合小圆孔,消除了方形型孔流量系数变化的影响,改变了活门型孔加工方法,减少了对人和环境的危害,提高了活门型孔的计量精度,减小了活门的液动力,具有极大的工程应用价值。 该算法可以实现将方形、梯形（含三角形）及其组合型孔等任意型孔的转化,具有工程上的普遍适用性。     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

不同环境因素对引压管腔动态特性影响

为了探索引压管腔在动态压力校准和使用中不同环境因素对动态特性的影响,推导了管腔传压模型和谐振频率关系式,确立了影响管腔动态特性的参数,包括静态压力、温度、气体介质等。采用引压管腔专用实验装置进行了不同环境参数状态的实验验证,结果表明:静态压力仅会影响管腔在谐振频率附近的输出,随着静态压力的增大而非线性增大,对动态特性并无明显改变;温度会改变管腔的谐振频率和动态特性,随着温度的升高,谐振频率增大但输出幅值随之减小;气体介质的不同会彻底改变管腔动态特性,主要取决于介质的声速。该研究为引压管腔在使用环境下数据的评价和数据修正上提供了一定参考依据。     

基于PIV技术的单圆孔脉冲射流流场特征

对稳态射流及脉冲射流冲击靶板时的流场特性结构进行了探索和分析。采用高频粒子图像测速技术,在射流管口到冲击靶板间距为6倍管径的条件下,对稳态射流进口雷诺数为6 000的稳态射流及脉冲频率为20 Hz的脉冲射流进行了实验测量,得到了射流核心区、壁面射流区及滞止区内的速度分布。研究发现:①由于射流剪切作用的影响,脉冲射流核心区的最大轴向脉动速度为稳态射流的3倍。②滞止区内,由于射流的剪切作用和壁面的滞止作用,导致了脉冲射流轴向速度梯度最大为稳态射流的2倍,同时,滞止区内的最大脉动速度是稳态射流脉动速度的3倍。③脉冲射流对壁面的卷吸以及旋涡的产生和传播过程,破坏了壁面射流区稳定的速度边界层。相比稳态射流,脉冲射流的流场增加了湍流相干结构的含能并产生周期性的大尺度卷吸涡。     

“蚌式”进气道附面层扫除特性风洞试验

以某低、高速风洞为平台,设计搭建了“蚌式”进气道附面层扫除特性测量试验系统,进行了不同流量系数和来流马赫数下进气道鼓包表面附面层扫除特性的风洞试验,通过对试验数据的整理、计算和对比分析同型号的飞行试验结果,研究了“蚌式”进气道鼓包表面附面层扫除特性。研究结果表明:在相同的来流马赫数下,随着流量系数的增大,鼓包表面附面层的扫除能力逐渐减弱;在亚声速工况的绝大多数流量范围内,鼓包表面压力系数沿鼓包中心线对称分布、压力梯度变化明显,且在不同截面沿主流方向具有增大的特征,鼓包构型对附面层扫除效果较强;超声速工况下具有明显附面层扫除能力的流量范围明显小于亚声速工况,进气道唇口形成的弓形激波是影响鼓包表面不同位置压力梯度变化的主要因素,进而决定着附面层扫除特性。在接近来流马赫数18及以上飞行工况下,附面层的扫除能力减弱,附面层分离加强,进而会造成较大的进气压力损失和畸变。     

脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

射频介质阻挡放电改善NACA 0015翼型气动性能的实验

介质阻挡放电(DBD)均匀稳定、易于敷设,是机翼/翼型等离子体流动控制(PFC)中最常用的激励方式。射频介质阻挡放电激励频率高、放电功率大,且能在流场中产生明显的加热,应用潜力大。采用射频电源驱动DBD激励器产生等离子体,分析放电的体积力、热特性和诱导流场特性,开展了射频介质阻挡放电改善NACA 0015翼型气动性能的实验,研究了占空比、调制频率、载波频率和电源功率等参数对流动控制效果的影响规律。结果表明:射频等离子体激励的体积力效应随激励电压的增大而增加;射频等离子体激励产生的热量在诱导的流场中进行传导,加速流场;当来流速度为20m/s,Re=3.36×10~5时,在翼型前缘施加激励,使翼型临界失速迎角推迟1°,最大升力系数增大6.43%,且在过失速迎角下仍具有流动控制效果,使升力下降变缓;调制频率越大,控制效果越好;存在最佳占空比、载波频率和功率,占空比对流场控制效果的影响最显著,最佳占空比、载波频率和功率分别为20%,460kHz和50W。射频等离子体激励以体积力效应、热效应和诱导壁面射流改善失速流场,使得NACA0015翼型气动性能极大改善,流动分离得到有效控制。     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.